基于PLC的细纱机电控部分设计

论文编号:ZD181  附任务书,大图,西门子公司S7－200PLC  论文字数:21010,页数:47

摘  要
                                         
细纱生产是纺纱过程的最后一道工序，细纱机是将粗纱或条子纱纺成一定支数的细纱，供捻线、机织或针织用。细纱机在生产中起着很重要的作用，控制系统性能的稳定直接影响到生产的成本。本设计就是将以前在细纱生产过程中的老式继电器控制，改成用自动化程度比较高的PLC控制，在此基础上实现细纱机的低速启动、高速启动、中途停车、提前落纱和紧急停车等主控制功能；实现电机严格按顺序启动、过载保护和漏电保护等保护功能；实现低速运行状态指示、高速运行状态指示、满纱指示、按故障性质发出停机报警信号等指示、报警功能，最终实现细纱机的稳定、可靠、安全运行。

  关键词：细纱机；PLC；自动控制

The electromechanics of spun yarn based on PLC accuses of designing partly
Abstract

It is end lines of process to spinning course for spun yarn not to produce, spinning frame spin certain spun yarn of number of yarn roving or strip yarn, available for twisting thread , the machine is woven or knitting. The spinning frame plays a very important role in production, the cost that the stability of controlling systematic function influenced production directly. It is to control the outdated relay while the spun yarn produces of before to originally design, make into and control with PLC with higher automatic degree, realize to launch , start , stop , fall yarn and is it control function mainly to stop promptly ahead of time midway at a high speed at a low speed spinning frame on this basis; Realize the electrical machinery is started in order strictly, overload protection and leaking electricity to protect etc. and protect the function; Realize low-speed operation state point out , high-speed operation state point out , full yarn point out , is it shut down alarm signal instruction , warning function to send out according to trouble nature, realize stability of the spinning frame , reliable , safe operation finally.

Keyword: The mechanics of spun yarn; PLC; Automatic control 

目  录

摘要…………………………………………………………………………………………Ⅰ
Abstract……………………………………………………………………………………Ⅱ
第一章    绪 论……………………………………………………………………………1
第二章    细纱工业简述………………………………………………………………… 3
2.1   细纱工艺简介………………………………………………………………… 3
2.2   细纱机简介…………………………………………………………………… 5  
第三章    硬件设计……………………………………………………………………… 7  
3.1   电机的选型…………………………………………………………………… 7               
3.2   PLC选型及外围电路的设计………………………………………………… 10
3.2.1 PLC的选型…………………………………………………………………… 10
3.2.2 模拟量扩展模块的选型………………………………………………………12
3.2.3 PLC的电源设计……………………………………………………………… 13
3.3   传感器的设计…………………………………………………………………14
3.3.1 行程开关的设计………………………………………………………………14
3.3.2 温度传感器的设计……………………………………………………………15
3.3.3 湿度传感器的设计……………………………………………………………16
3.4   低压电器的选型………………………………………………………………17
3.4.1 接触器的选型…………………………………………………………………17
3.4.2 继电器的选型…………………………………………………………………19
3.4.3 主令电器的选择………………………………………………………………20
第四章    软件设计………………………………………………………………………21
4.1   细纱生产工艺分析……………………………………………………………21
4.2   系统控制程序…………………………………………………………………24
第五章    控制程序调试…………………………………………………………………27
5.1   STEP 7开发环境介绍…………………………………………………………27
5.2   控制程序的调试………………………………………………………………29
第六章    系统抗干扰分析及注意问题…………………………………………………31
6.1     系统干扰以及抑制措施……………………………………………………31
    6.2     系统应用中需要注意的问题………………………………………………34
结论…………………………………………………………………………………………38
参考文献……………………………………………………………………………………39
致谢…………………………………………………………………………………………40
附录:梯形图…………………………………………………………………………………41

相关论文